Frequently Asked Questions
Q: What kind of LEDs are used in X75?
A: 12 x CREE XHP70.3 HI LEDs.
Q: What’s the color temperature of X75?
A: 6500K.
Q: What battery does the X75 support?
A: The light is built in a 14.4V/61.2Wh rechargeable Li-ion battery pack.
Q: Where is its USB-C port located?
A: 
Q: How can I get the PD100W fast charge to full charge in 1hour?
A: The standard charger included is PD60W with Emark cable, which can be fully charged in 1.5 hours. Customers can get a 100W AC Power adapter from the market and use our included Emark cable to support PD100W to speed up to full charge in 1hour.
Q: Whether X75 is waterproof?
A: When you see so many gaps built in the x75, you must be concerned about its water resistance. In fact, this torch is waterproof underwater two meters, IP68. We adopt internal waterproof designs such as physical isolation, contact energization, and sealed conduit.
Q: Does X75 have Power Mode and ECO Mode?
A: Yes, X75 is designed with Power mode and ECO mode for energy saving. Under Power mode, the regulated temperature is 75 degrees. The output at Turbo max would be stepped down to 30,000lumens from 80,000lumens should the temperature is too high. Under ECO mode, the regulated temperature is 65 degrees. The output at Turbo max would be stepped down to 13,000lumens from 80,000lumens should the temperature is too high.
Q: How to set ECO mode and Power mode?
A: When the light is off, quickly click the Auxiliary Switch (Above one) 10 times above to exchange mode between ECO mode and Power mode. When the light is dimmer, it means ECO mode. When the light is brighter, it means Power mode.
Q: Does X75 have overheat protection?
A: Yes. The light will accumulate a lot of heat when used at high-output mode for extended periods. When the light reaches set temperature or above, the light will automatically step down a few lumens to reduce the temperature. When the temperature drops below the set temperature, it allows the user to select the mode.
Q: Does X75 have a heat dissipation system?
A: Sure! For high-lumen flashlights, how to control the heat becomes especially important. The x75 utilizes the principle of air duct heat dissipation and designs a cooling fan for heat dissipation, which can quickly and efficiently inhale cold air and discharge hot air.
Q: Whether the cooling fan can be controlled?
A: There are two modes: Windy Mode or Non-Wind Mode. Under Windy mode, the cooling fan is Intelligent, which would be turned on automatically when the temperature is high. While, also, users can also turn it off to set the Non-wind mode if they need it works in a quiet environment.
Q: How to set the Windy Mode or Non-Wind Mode?
A: When the flashlight is off, long-press the Auxiliary Switch (Above one) to exchange the Windy Mode or Non-Wind Mode. When the battery indicator is green, which means Windy Mode is active. When the battery indicator is red, which means Non-Wind Mode is active.
Q: Is it normal that the cooling fan still working after I turn off the flashlight?
A: The operation of the intelligent cooling fan is controlled by the temperature of the flashlight. If the temperature of the flashlight is high, the cooling fan will be turned on automatically. Even when the flashlight is turned off, but the temperature of the flashlight is still high, the fan will continue to run to dissipate heat. When the heat drops to a safe temperature, about 50 degrees, the fan stops running and shuts down automatically (may need several minutes after the flashlight is turned off). While, also, users can also turn it off if they need it works in a quiet environment. Please note that it is not recommended to turn off the fan manually. When the fan is turned off, the casing of the flashlight cannot cool down effectively, and there is a risk of burns.
Q: If there is water/sand/dust in the fan, how to clean it?
A: The cooling fan is designed detachable and maintainable. The cooling fan can be taken off by unscrewing the thread. Wash them in water and dry them with a hair dryer.
Q: What are the default settings when X75 is out of the factory?
A: The default setting for X75 is insulated the power by the plastic film; Lockout Mode; ECO mode; Low power battery pack,
Please remove the insulating film, unlock the flashlight and charge the battery pack before the first use.
Q: When the flashlight is hot, whether it can be dropped into water to cool down?
A: Can not. Do not submerge the flashlight into any liquid when it is hot. Doing so may cause irreparable damage to the light due to the sharp difference in the glass lens.
Q: What does it mean by “PD/QC full protocol” on the battery pack?
A: X75 supports QC2.0, QC3.0, PD2.0, PD3.0, AFC/FCP/ SCP/ VOOC input and output protocol, compatible with BC1.2/IPHONE
Charging input: 5V/3A 9V/3A 12V/3A 15V/3A 20V/3A
Power bank output: 5V/3A 9V/3A 12V/3A 15V/3A 20V/3A
English 
中文 